Passer au contenu principal
Photos
Photos
Conseils
Magazine Houzz
Discussions Houzz
Études Houzz
Se connecter
Houzz Logo Print
Parcourir les discussions
PeintureDécoration intérieureDilemme déco
klmcdonald731

Help with DIY Project - Painting Antique Furniture

Kristen
il y a 5 ans

Hi everyone! I've had a cute antique vanity and side table for 15 years and want to update them to give them a more adult, modern look. I am not good at DIY projects and don't know where to begin to make sure I do this properly. Every instruction or "how to" I find is taking a piece from bare wood to painted, but these have already been painted and are chipped in several places. I'd love some advice from someone who has upcycled antique furniture that's already been painted! Do I need to get all of the paint off? Just sand lightly? Is there a different type of primer I will need than if it was bare? Will I need an electric sander or just normal sandpaper or a sanding block?


I'd also love recommendations for primers, paints, and protective coatings. I want to do an antique matte black for both with brass hardware. I've added some photos to show my current white pieces and some inspiration for what I want the end result to look like!


Thank you!!!


BEFORE:






AFTER (HOPEFULLY)

I know these look more navy, but I want to do a true antique matte black. This is just for the idea.







Réponse sélectionnée
  • Kristen
    Auteur d'origine
    il y a 4 ans

    BEFORE -


    ONE COAT after sanding


    Already posted the photo after two coats. Here's after I did one thin layer of black wax with a painting cloth and new hardware! It's certainly not perfect but I am happy with the results!





    Commentaires (26)

    • PRO
      1625 DB
      il y a 5 ans

      You'll need to sand pretty agressively -- with a power tool if one is availble. The goal is not to strip, but to get the flakes of paint off and then make a 'rough' surface that paint will stick to. Then prime and paint. Painting with a brush once that's done will leave a streaky finish -- its not a high end solution, but spray paint would give the most even finish. Spray paint also looks MUCH better matte than brush paint.

    • Olychick
      il y a 5 ans

      Your inspiration pics are wonderful. Good luck and be sure to post an "after" picture!

    • lindahambleton
      il y a 5 ans

      An electric “palm” sander is easy to use. I have seen nice small hobby kind of sprayers but I have never used one.

      Sherwin Williams have quality primers and there is usually at least one knowledgable employee to help you.

    • cat_ky
      il y a 5 ans
      Dernière modification :il y a 5 ans

      I use a mouse sander for pieces like that. It works great. A very good quality primer, and buy paint meant for furniture. It has a tougher finish.

    • Kathi Steele
      il y a 5 ans

      I strip first, then sand. I have used all kinds of strippers. None especially stand out. It depends on if I am in a small contained area or the garage.

      You will need to get a high quality sprayer and spray them, especially for a matte finish.

    • Anne Duke
      il y a 5 ans
      I used cans of matte black spray paint on a dining table and it came out really well. Took a lot of cans doing very light coats and light sanding in between. Finished with a clear coat. It was a long project, but gave new life to that table.
    • zzuoh99
      il y a 5 ans
      Have you investigated Annie Sloan chalk paint? Comes in a nice array of colors and you literally can paint without doing any stripping. Clean the piece and paint. Resulting finish is very nice. You can also add a protective wax.
    • ljptwt7
      il y a 5 ans
      I have used Anne Sloane Chalk paint on several items. Love it. But if you have chipping paint I would sand off any loose paint and make sure area is level/smooth ( you don't want it obvious after painting). But no primer neccessary.
    • ShadyWillowFarm
      il y a 5 ans
      Chalk paint is very forgiving - you’ll love it. If you have chipped paint, I’d sand it smooth, with sandpaper or a sander depending on how bad it’s chipped. Research chalk paint brands - Annie is very expensive and there are more options out there. Annie says one coat and she lies. Mostly all of them require 2 coats for a nice finish. Top with a clear coat finish, General Finishes makes a great one. Have fun and please post a pic of your finished project! YouTube is a great source of tutorials.
    • Lauren Lista
      il y a 5 ans
      Definitely sand the whole piece to smooth so you don't see chip marks under the new paint. Use a power sander for best results and an easier job. I like the idea of chalk paint, and I think you can decide if you want a top coat after. I love your mismatched knobs!
    • Kathleen K
      il y a 5 ans
      Should check for lead paint before sanding if they are really old.

      We should trade projects. I have a black little end table i need to paint light.

      Sand and wipe off dust to get a smooth finish. There special tack cloths that refinisher use to wipe dust from sanding between coats. I did that with oil based paints and epoxy tub paint but I think chalk paints would be easier. You would only need to wipe the sanding dust off once. For a matte finish it does need a smooth sanding. Satin finish would show less flaws than a flat matte or high gloss.

      I would love to know the story on the desk design. Built for those old manual typewriters?
    • Kristen
      Auteur d'origine
      il y a 5 ans
      Thank you to everyone for the suggestions! I will plan to get my hands on a power sander and look into chalk paint. Is there any benefit to priming with chalk paint even though some said you don’t need to? Would it be beneficial in the long run to do both?

      I plan to wait to tackle this until MN weather gets a bit nicer, but will be sure to post after photos! As far as history I wish I knew more, but my mom found it for me when I was 11 at a little antique shop and let me pick out my own knobs to match my room. Now I’m 26 and still use it! My plan for future use will be in a front entry as a place for keys and mail and “junk drawer” items. Here’s how I had it styled before
    • apple_pie_order
      il y a 5 ans

      The furniture is old enough to have had lead paint. Please test for it before you start sanding- a test kit is only $10 at the local hardware or big box store. The pieces will paint up nicely.

    • ShadyWillowFarm
      il y a 5 ans
      You don’t need to prime with chalk paint.
    • Rory (Zone 6b)
      il y a 5 ans

      I would chalk paint those. I have made my own with plaster of paris and regular latex paint. Just sand off loose paint first. No need to prime. It dries quickly and all you need to do after is wax and buff.

    • rdy2retire
      il y a 5 ans

      Annie Sloan - graphite and black wax! Awesome black matte! 2 coats of paint. The wax gives it a great look!

    • PRO
      User
      il y a 5 ans

      All of our pieces are sanded then prime with cover stain before finishing.

    • Kristen
      Auteur d'origine
      il y a 4 ans


      Started with the side table as my test piece. This was after sanding the entire table with medium grit sandpaper until smooth and two coats of Annie Sloan graphite chalk paint (needs a few touch-ups below the bottom drawer) Next I plan to use black wax to darken! It's turning out great so far.

    • cat_ky
      il y a 4 ans

      Congratulations. It looks very nice. It was good to start with the smaller piece first.

    • katinparadise
      il y a 4 ans

      following

    • Kristen
      Auteur d'origine
      il y a 4 ans

      It's taken me a while but I've finally finished the vanity - the wood wasn't in as great of shape so it was a bit tougher!


      Now I just need to decide on knobs. Should I get matching knobs with the side table or do something a bit larger/more interesting on the vanity? My only limitation is the two bottom drawers have larger holes, so the back of the knobs need to be a bit wider.




    • Tootsie
      il y a 4 ans

      Use a washer to hold the screw in place.

    • Kristen
      Auteur d'origine
      il y a 4 ans

      Yes I’ve used washers before with the other knobs but some Ive tried are skinny enough that the backs fall through the front as well. I wouldn’t want a washer on the front

    • ci_lantro
      il y a 4 ans

      One other thing re the knobs. When you find one that works, cut a short length of clear tubing the thickness of the drawer front (an approximately the diameter of the hole) to thread the knob screw thru. It will help fill up the hole and keep the knob from wobbling in the hole.

    • ShadyWillowFarm
      il y a 4 ans

      Gorgeous!

    Sponsorisé

    Rechargez la page pour ne plus voir cette annonce spécifique

    France
    Personnaliser mon expérience à l'aide de cookies

    Houzz utilise des cookies et d'autres technologies de suivi similaires pour personnaliser mon expérience utilisateur, me proposer du contenu pertinent et améliorer ses produits et services. En cliquant sur « Accepter », j'accepte l'utilisation des cookies telle qu'elle est décrite plus en détail dans la Politique d'Utilisation des Cookies de Houzz. Je peux rejeter les cookies non essentiels en cliquant sur « Tout rejeter » ou « Gérer mes préférences ».